VITO FOR ROOFS
Acrylic waterproofing and insulating material with high elasticity for roofs. It is an economic and reliable solution to waterproofing. It has good adhesion to every structural surface (concrete, brick, wood, metal, etc.). Exhibits excellent resistance to adverse weather conditions and UV radiation, retaining its elasticity at temperatures ranging from -20°C to +100°C.
• Water insulating material for roofs
• Great elasticity
• Certified Cool Paint for Roofs
SPECIAL CHARACTERISTICS
Certified from the University of Athens, Department of Physics, as a cool material for roofs with the following properties:
Initial Total Solar Reflectance SR=0.84 (300-2500nm) (ASTM 903-96 and ASTM G 159-98)
Infrared Emittance Factor ε = 0.89 (ASTM E 408-71-2002)
Solar Reflectance Index SRI = 106 (ASTM E 1980-01)
COLOURS
Available in white.
TECHNICAL SPECIFICATIONS
- Surface drying time 2-3h
- Water dilution percentage 0-5%
- Spreading rate 2-3m2/lt
- Application by brass
- Application by roller
- Application by Spray gun
INSTRUCTIONS
SURFACE PREPARATION
Surfaces should be smooth, clean and dry, free from grease, dust, loose or flaking paint.
Cracks or joints should first be filled.
Surfaces should be primed with Durovit diluted up to 30% with Brush Solvent T 300.
APPLICATION
Stir well before use. Apply cross-wise two coats, allowing 24 hours between each coat application, by roller, brush or airless spray gun diluted up to 5% with water for the first coat. Apply the second coat without dilution. Do not apply at temperature below 5°C, above 35°C and / or relative humidity above 70%.
Avoid application when rain or frost is expected in the next 48 hours.
It is touch-dry after 2-3 hours and can be recoated after 24-48 hours. Drying time depends on weather conditions (humidity and temperature).
Tools must be cleaned immediately after use with water and if needed with soapy water or a detergent.
Acrylic waterproofing and insulating material with high elasticity for roofs. It is an economic and reliable solution to waterproofing. It has good adhesion to every structural surface (concrete, brick, wood, metal, etc.). Exhibits excellent resistance to adverse weather conditions and UV radiation, retaining its elasticity at temperatures ranging from -20°C to +100°C.
• Water insulating material for roofs
• Great elasticity
• Certified Cool Paint for Roofs
SPECIAL CHARACTERISTICS
Certified from the University of Athens, Department of Physics, as a cool material for roofs with the following properties:
Initial Total Solar Reflectance SR=0.84 (300-2500nm) (ASTM 903-96 and ASTM G 159-98)
Infrared Emittance Factor ε = 0.89 (ASTM E 408-71-2002)
Solar Reflectance Index SRI = 106 (ASTM E 1980-01)
COLOURS
Available in white.
TECHNICAL SPECIFICATIONS
- Surface drying time 2-3h
- Water dilution percentage 0-5%
- Spreading rate 2-3m2/lt
- Application by brass
- Application by roller
- Application by Spray gun
INSTRUCTIONS
SURFACE PREPARATION
Surfaces should be smooth, clean and dry, free from grease, dust, loose or flaking paint.
Cracks or joints should first be filled.
Surfaces should be primed with Durovit diluted up to 30% with Brush Solvent T 300.
APPLICATION
Stir well before use. Apply cross-wise two coats, allowing 24 hours between each coat application, by roller, brush or airless spray gun diluted up to 5% with water for the first coat. Apply the second coat without dilution. Do not apply at temperature below 5°C, above 35°C and / or relative humidity above 70%.
Avoid application when rain or frost is expected in the next 48 hours.
It is touch-dry after 2-3 hours and can be recoated after 24-48 hours. Drying time depends on weather conditions (humidity and temperature).
Tools must be cleaned immediately after use with water and if needed with soapy water or a detergent.