ACRYLIC WATER-BASED PAINT FOR CONCRETE SURFACES
High quality water-based acrylic concrete paint, specially formulated for direct application on concrete, plaster, brick and other alkaline masonry surfaces. It provides great hiding power, high spreading rate and exceptional resistance to washing and adverse weather conditions. Available in four shades.
Premium quality acrylic paint for exterior use. Due to its special formula, it is suitable for application on concrete and alkaline masonry surfaces. It provides great hiding power, high spreading rate and exceptional fastness to washing and atmospheric weathering.
• Concrete paint
• Direct application on concrete and alkaline masonry surfaces
• High spreading rate
COLOURS
Available in white and 4 ready-made shades (see relevant colour card).
TECHNICAL SPECIFICATIONS
- Surface drying time 30-60 min
- Water dilution percentage 0-10%
- Spreading rate 12-15 m2/lL
- Application by brass
- Application by roller
- Application by Spray gun
INSTRUCTIONS
SURFACE PREPARATION
Surfaces should be smooth, clean and dry, free from grease, dust, loose or flaking paint.
To fill any cracks or holes use Acrylic Putty.
Surfaces previously covered with water paints or distempers (lime wash or ceiling white) should be primed with Acrylan Unco Eco, Durovit or Vitosin.
New surfaces made of plaster, concrete, cement, plasterboard, etc. should be first primed with Acrylan Unco Eco or Durovit.
APPLICATION
Stir well before use. Apply two coats by roller, brush or airless spray gun diluted up to 10% with water. Do not apply at temperature below 5°C, above 35°C and / or relative humidity above 70%. Avoid application when rain or frost is expected in the next 48 hours.
It is touch-dry after 30-60 minutes and can be recoated after 3-4 hours. Drying time depends on weather conditions (humidity and temperature).
Allow at least 3 weeks before cleaning and washing newly painted surfaces with Concrete Paint. Wash gently with water using a soft sponge. In case of bad stains, use a mild colourless detergent or soapy water.
Tools must be cleaned immediately after use with water and if needed with soapy water or a detergent.
High quality water-based acrylic concrete paint, specially formulated for direct application on concrete, plaster, brick and other alkaline masonry surfaces. It provides great hiding power, high spreading rate and exceptional resistance to washing and adverse weather conditions. Available in four shades.
Premium quality acrylic paint for exterior use. Due to its special formula, it is suitable for application on concrete and alkaline masonry surfaces. It provides great hiding power, high spreading rate and exceptional fastness to washing and atmospheric weathering.
• Concrete paint
• Direct application on concrete and alkaline masonry surfaces
• High spreading rate
COLOURS
Available in white and 4 ready-made shades (see relevant colour card).
TECHNICAL SPECIFICATIONS
- Surface drying time 30-60 min
- Water dilution percentage 0-10%
- Spreading rate 12-15 m2/lL
- Application by brass
- Application by roller
- Application by Spray gun
INSTRUCTIONS
SURFACE PREPARATION
Surfaces should be smooth, clean and dry, free from grease, dust, loose or flaking paint.
To fill any cracks or holes use Acrylic Putty.
Surfaces previously covered with water paints or distempers (lime wash or ceiling white) should be primed with Acrylan Unco Eco, Durovit or Vitosin.
New surfaces made of plaster, concrete, cement, plasterboard, etc. should be first primed with Acrylan Unco Eco or Durovit.
APPLICATION
Stir well before use. Apply two coats by roller, brush or airless spray gun diluted up to 10% with water. Do not apply at temperature below 5°C, above 35°C and / or relative humidity above 70%. Avoid application when rain or frost is expected in the next 48 hours.
It is touch-dry after 30-60 minutes and can be recoated after 3-4 hours. Drying time depends on weather conditions (humidity and temperature).
Allow at least 3 weeks before cleaning and washing newly painted surfaces with Concrete Paint. Wash gently with water using a soft sponge. In case of bad stains, use a mild colourless detergent or soapy water.
Tools must be cleaned immediately after use with water and if needed with soapy water or a detergent.