AQUAVIT ECO
TECHNICAL SPECIFICATIONS
- Surface drying time 1-2 h
- Water dilution percentage 10-15%
- Spreading rate 9-13 m2/lt
- Application by brass
- Application by roller
- Application by Spray gun
INSTRUCTIONS
SURFACE PREPARATION
Surfaces should be smooth, clean and dry, free from grease or dust and sanded.
Properly prepared wooden surfaces (treated with wood preservative Diaxyl Water based, stoppered, filled with Acrylic Putty and sanded down to a clean, smooth surface) should be coated with Velatura Eco Water based. Then use an appropriate abrasive paper to produce a smooth surface and remove the dust.
New surfaces made of plaster, concrete, cement, plasterboard, etc. should be first primed with Acrylan Unco Eco or Blanco Eco.
Surfaces stained from smoke, graffity, coffee or any other kind of stain should first be primed with Blanco Eco.
Metallic surfaces should be coated with an anticorrosive primer (Anti-Rust Primer, Minio New Type or Metal Primer).
Glossy metallic surfaces (aluminum, galvanized steel etc) should be first coated with Velatura Eco Water based.
APPLICATION
Stir well before use. Apply one or two coats by roller or brush diluted up to 5-10% with water or by spray gun diluted up to 10-15% with water. Do not apply at temperatures below 5oC, above 35oC and/or relative humidity above 80%.
It is touch-dry after 1-2 hours and can be recoated after 6-8 hours. Drying time depends on weather conditions (humidity and temperature). Allow at least 3 weeks before cleaning and washing newly painted surfaces with Aquavit Eco. Wash gently with water using a soft sponge. In case of bad stains, use a mild colourless detergent or soapy water. After paint application, seal the pail and store it in temperatures between 5oC and 35oC for future use.
Tools must be cleaned immediately after use with water and if needed with soapy water or a detergent. Do not dispose of liquid waste into ground water table. Unused paint requires special handling for safe disposal. Advice regarding disposal and collection should be sought from the local authority.
TECHNICAL SPECIFICATIONS
- Surface drying time 1-2 h
- Water dilution percentage 10-15%
- Spreading rate 9-13 m2/lt
- Application by brass
- Application by roller
- Application by Spray gun
INSTRUCTIONS
SURFACE PREPARATION
Surfaces should be smooth, clean and dry, free from grease or dust and sanded.
Properly prepared wooden surfaces (treated with wood preservative Diaxyl Water based, stoppered, filled with Acrylic Putty and sanded down to a clean, smooth surface) should be coated with Velatura Eco Water based. Then use an appropriate abrasive paper to produce a smooth surface and remove the dust.
New surfaces made of plaster, concrete, cement, plasterboard, etc. should be first primed with Acrylan Unco Eco or Blanco Eco.
Surfaces stained from smoke, graffity, coffee or any other kind of stain should first be primed with Blanco Eco.
Metallic surfaces should be coated with an anticorrosive primer (Anti-Rust Primer, Minio New Type or Metal Primer).
Glossy metallic surfaces (aluminum, galvanized steel etc) should be first coated with Velatura Eco Water based.
APPLICATION
Stir well before use. Apply one or two coats by roller or brush diluted up to 5-10% with water or by spray gun diluted up to 10-15% with water. Do not apply at temperatures below 5oC, above 35oC and/or relative humidity above 80%.
It is touch-dry after 1-2 hours and can be recoated after 6-8 hours. Drying time depends on weather conditions (humidity and temperature). Allow at least 3 weeks before cleaning and washing newly painted surfaces with Aquavit Eco. Wash gently with water using a soft sponge. In case of bad stains, use a mild colourless detergent or soapy water. After paint application, seal the pail and store it in temperatures between 5oC and 35oC for future use.
Tools must be cleaned immediately after use with water and if needed with soapy water or a detergent. Do not dispose of liquid waste into ground water table. Unused paint requires special handling for safe disposal. Advice regarding disposal and collection should be sought from the local authority.